Welcome to Bafinasa official website!

Emerald Green Mesh High Slit Bodycon Dress

Source:News / Time:2026-11-14

Most of the money in a Emerald Green Mesh High Slit Bodycon Dress sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing. A Emerald Green Mesh High Slit Bodycon Dress reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together. It helps to separate what the customer sees from what the factory feels. The outside is mesh in green, the inside is structure, and the two have to agree on the same sample. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. We start with mesh on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. For mesh, order five to eight percent extra. Cutting around a shade band costs more than the cloth.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Zip placement decides how the dress goes on. A centre-back zip is neat; a side zip is easier to wear and harder to hide.

The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Specification, item by item

Shellmesh, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Liningbodice lined, skirt lined
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ100 pcs per colour

Failure points worth designing out

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Schedule an in-line check after the side panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.

Customisation that does not break the price

  • Bonded or sewn finish at the neckline and armhole.
  • Panel count from four to eight, with a small cost difference per unit.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top