Welcome to Bafinasa official website!

Royal Blue Mesh Sleeveless Bodycon Dress

Source:News / Time:2026-11-14

Written down, the request is royal blue mesh sleeveless bodycon dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining.

We keep the sleeveless as its own pattern piece so it can be changed without re-cutting the body. If the sleeveless is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

The sheet we need before costing

Shellmesh, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayblue
Lininghalf lined to the hip
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ300 pcs per style

What to check before bulk

  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Options on the table

  • Bonded or sewn finish at the neckline and armhole.
  • Panel count from four to eight, with a small cost difference per unit.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Private label: woven label, care label and hangtag to your artwork.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top