Welcome to Bafinasa official website!

Mesh Long Sleeve Bodycon Dress

Source:News / Time:2026-11-14

Most of the money in a Mesh Long Sleeve Bodycon Dress sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. We start with mesh on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

Structure and seams

Most of the handwork sits in a handful of steps, and each one has a right order. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.

The long sleeve is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. Check the long sleeve after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.

Specification, item by item

Shellmesh, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningbodice lined, skirt lined
Closurecovered button placket
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ50 pcs sample order

The places this usually goes wrong

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. In bulk the failures cluster: skipped stitches on the side panel, shading between panels, and hems that go wavy after pressing. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Customisation that does not break the price

  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Private label: woven label, care label and hangtag to your artwork.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top