Welcome to Bafinasa official website!

Cheap Emerald Green Ribbed Knit Bodycon Dress

Source:News / Time:2026-11-14

A Cheap Emerald Green Ribbed Knit Bodycon Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. It helps to separate what the customer sees from what the factory feels. The outside is knit in green, the inside is structure, and the two have to agree on the same sample. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Most of the money in a Cheap Emerald Green Ribbed Knit Bodycon Dress sits in three places: the cloth, the side panel, and the labour that keeps the centre front seam flat after pressing.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Under 200 gsm, plan to interface the side panel. Without it, the seam ridge shows through at the first press.

Where the shape comes from

The build follows the same order on every size. These are the steps where the shape is won or lost. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it. Lining a bodycon is unusual. On light cloth a bonded second layer is cleaner than a sewn lining. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet.

Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.

Spec sheet, line by line

Shellknit, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Lininghalf lined to the hip
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ50 pcs sample order

The places this usually goes wrong

  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

Options on the table

  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Private label: woven label, care label and hangtag to your artwork.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top