Welcome to Bafinasa official website!

Women's Red Ribbed Knit Bodycon Dress

Source:News / Time:2026-11-14

A Women's Red Ribbed Knit Bodycon Dress reads as a short brief until the pattern is cut, and the shape only holds when the side panel, the centre front seam and the hem allowance are settled together. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.

Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. We start with knit on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. Test elasticity on the cloth: measure how far a 10 cm strip recovers after stretching, and write the number on the sheet. Join with a stretch stitch and press the seams open. A straight stitch pops the first time the wearer sits down. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.

The neckline reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. When the brief names the neckline, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Specification, item by item

Shellknit, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwayred
Liningbodice lined, skirt lined
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time10-14 days on stock cloth
MOQ50 pcs sample order

What to check before bulk

  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Cloth with insufficient recovery, so the dress grows through the day.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. In bulk the failures cluster: skipped stitches on the side panel, shading between panels, and hems that go wavy after pressing. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.

Changes we can make at sample stage

  • Neckline: square, sweetheart, halter or asymmetric.
  • Bonded or sewn finish at the neckline and armhole.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Private label: woven label, care label and hangtag to your artwork.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top