Welcome to Bafinasa official website!

Emerald Green Stretch Spandex Club Bodycon Dress

Source:News / Time:2026-11-14

Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the side panel. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. It helps to separate what the customer sees from what the factory feels. The outside is bandage knit or heavy ponte in green, the inside is structure, and the two have to agree on the same sample.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. We start with bandage knit or heavy ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

Structure and seams

Most of the handwork sits in a handful of steps, and each one has a right order. The hem is the hard part. A twin needle or a coverstitch keeps it flat; a plain hem waves. Bandage and ponte styles are built from panels. The number of panels decides how the garment follows the body and how much labour sits in it.

If the neckline is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. Check the neckline after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

On this style the difference between a good and a poor fit is usually two centimetres at the centre front seam, not a redesign. For Bodycon Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the side panel.

Specification, item by item

Shella bandage knit or a heavy ponte with good recovery, swatch-approved, one dye lot for bulk
Bodybodycon dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Liningfully lined, bagged hem
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time10-14 days on stock cloth
MOQ150 pcs per style

Where this style fails in production

  • A fused hem used to control the edge, making it stiff and visibly different from the body.
  • Too few panels, so the garment pulls across the hip and the seam line distorts.
  • A standard stitch instead of a stretch stitch, giving popped seams after the first wear.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Customisation that does not break the price

  • Panel count from four to eight, with a small cost difference per unit.
  • Bonded or sewn finish at the neckline and armhole.
  • Sleeve: sleeveless, cap, or long sleeve in the same cloth.
  • Neckline: square, sweetheart, halter or asymmetric.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top