Wholesale Emerald Green Double Breasted Blazer Office Dress for Office
We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.
Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth.
Structure and seams
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.
If the double breasted is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. When the brief names the double breasted, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. Shoulder and neckline decide whether a Wholesale Emerald Green Double Breasted Blazer Office Dress for Office looks expensive. Both are set by the block, not by the sewing. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | green |
| Lining | fully lined, bagged hem |
| Closure | invisible centre-back zip |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 50 pcs sample order |
The places this usually goes wrong
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing.
Customisation that does not break the price
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Single or double breasted front, without re-cutting the back.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.