Welcome to Bafinasa official website!

Bulk Black Tailored Blazer Office Dress

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Bulk Black Tailored Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Written down, the request is bulk black tailored blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

Structure and seams

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

We keep the tailored as its own pattern piece so it can be changed without re-cutting the body. The tailored reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Shoulder and neckline decide whether a Bulk Black Tailored Blazer Office Dress looks expensive. Both are set by the block, not by the sewing. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwayblack
Liningfully lined, bagged hem
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ300 pcs per style

What to check before bulk

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing.

What we can change for you

  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Single or double breasted front, without re-cutting the back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top