Welcome to Bafinasa official website!

Bulk Navy Blue Trench Blazer Office Dress

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. A Bulk Navy Blue Trench Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together.

Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet.

Where the shape comes from

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.

When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaynavy
Liningunlined with faced seams
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time15-20 days with handwork
MOQ150 pcs per style

Failure points worth designing out

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

What we can change for you

  • Vent, back seam, or plain back.
  • Single or double breasted front, without re-cutting the back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top