Welcome to Bafinasa official website!

Wholesale Burgundy Belted Blazer Office Dress

Source:News / Time:2026-11-14

Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. A Wholesale Burgundy Belted Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening.

How it is built

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.

When the brief names the belted, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. Check the belted after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Shoulder and neckline decide whether a Wholesale Burgundy Belted Blazer Office Dress looks expensive. Both are set by the block, not by the sewing. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwayburgundy
Lininghalf lined to the hip
Closureinvisible centre-back zip
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

What to check before bulk

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.

What we can change for you

  • Vent, back seam, or plain back.
  • Single or double breasted front, without re-cutting the back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top