Welcome to Bafinasa official website!

Wholesale Emerald Green Work Blazer Dress

Source:News / Time:2026-11-14

It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in green, the inside is structure, and the two have to agree on the same sample. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. Written down, the request is wholesale emerald green work blazer dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.

Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

What goes on the spec sheet

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Liningbodice lined, skirt lined
Closureinvisible centre-back zip
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ100 pcs per colour

The places this usually goes wrong

  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

What we can change for you

  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Single or double breasted front, without re-cutting the back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Private label: woven label, care label and hangtag to your artwork.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top