Welcome to Bafinasa official website!

Wholesale Camel Structured Blazer Office Dress

Source:News / Time:2026-11-14

A Wholesale Camel Structured Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Most of the money in a Wholesale Camel Structured Blazer Office Dress sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.

Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

Construction notes

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaycamel
Liningunlined with faced seams
Closurestretch panel, no zip
Size run34-44 with a regional grade
Sample lead time10-14 days on stock cloth
MOQ150 pcs per style

Where this style fails in production

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.

Customisation that does not break the price

  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Single or double breasted front, without re-cutting the back.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top