Welcome to Bafinasa official website!

Bulk Black Mini Blazer Office Dress

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Written down, the request is bulk black mini blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. A Bulk Black Mini Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

If the lapel is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. We keep the lapel as its own pattern piece so it can be changed without re-cutting the body.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthmini
Colourwayblack
Liningfully lined, bagged hem
Closureinvisible centre-back zip
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ100 pcs per colour

Where this style fails in production

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

Customisation that does not break the price

  • Vent, back seam, or plain back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Single or double breasted front, without re-cutting the back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top