Wholesale Camel Notch Lapel Blazer Office Dress
This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.
Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet.
Construction notes
The build follows the same order on every size. These are the steps where the shape is won or lost. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.
Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.
Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
The sheet we need before costing
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | camel |
| Lining | fully lined, bagged hem |
| Closure | concealed side zip |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 15-20 days with handwork |
| MOQ | 300 pcs per style |
Failure points worth designing out
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
Changes we can make at sample stage
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Vent, back seam, or plain back.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.