Wholesale Burgundy Sleeveless Blazer Office Dress for Office
Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. Written down, the request is wholesale burgundy sleeveless blazer office dress for office: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Most of the money in a Wholesale Burgundy Sleeveless Blazer Office Dress for Office sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in burgundy, the inside is structure, and the two have to agree on the same sample.
Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.
How it is built
Most of the handwork sits in a handful of steps, and each one has a right order. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.
We keep the sleeveless as its own pattern piece so it can be changed without re-cutting the body. Check the sleeveless after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | burgundy |
| Lining | unlined with faced seams |
| Closure | stretch panel, no zip |
| Size run | 34-44 with a regional grade |
| Sample lead time | 15-20 days with handwork |
| MOQ | 50 pcs sample order |
Failure points worth designing out
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.
Options on the table
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Single or double breasted front, without re-cutting the back.
- Vent, back seam, or plain back.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Private label: woven label, care label and hangtag to your artwork.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.
If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.