Wholesale White Long Sleeve Blazer Office Dress
A Wholesale White Long Sleeve Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Written down, the request is wholesale white long sleeve blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.
Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press.
Construction notes
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.
When the brief names the long sleeve, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. We keep the long sleeve as its own pattern piece so it can be changed without re-cutting the body.
On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | white |
| Lining | unlined with faced seams |
| Closure | stretch panel, no zip |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 15-20 days with handwork |
| MOQ | 50 pcs sample order |
The places this usually goes wrong
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing.
What we can change for you
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Single or double breasted front, without re-cutting the back.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.