Welcome to Bafinasa official website!

Bulk Midi Blazer Office Dress Online

Source:News / Time:2026-11-14

Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount.

Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.

When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. If the lapel is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

What goes on the spec sheet

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthmidi
Colourwaybuyer colourway, lab-dipped under two lights
Liningbodice lined, skirt lined
Closurestretch panel, no zip
Size run34-44 with a regional grade
Sample lead time10-14 days on stock cloth
MOQ100 pcs per colour

Where this style fails in production

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.

Changes we can make at sample stage

  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Vent, back seam, or plain back.
  • Private label: woven label, care label and hangtag to your artwork.
  • Private label: woven label, care label and hangtag to your artwork.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top