Wholesale Camel Midi Blazer Office Dress for Office
Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.
Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.
Where the shape comes from
The build follows the same order on every size. These are the steps where the shape is won or lost. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.
Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | midi |
| Colourway | camel |
| Lining | fully lined, bagged hem |
| Closure | covered button placket |
| Size run | 34-44 with a regional grade |
| Sample lead time | 15-20 days with handwork |
| MOQ | 50 pcs sample order |
Failure points worth designing out
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.
Options on the table
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Single or double breasted front, without re-cutting the back.
- Vent, back seam, or plain back.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Private label: woven label, care label and hangtag to your artwork.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.