Wholesale Burgundy Corporate Blazer Dress
A Wholesale Burgundy Corporate Blazer Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. A Wholesale Burgundy Corporate Blazer Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together.
We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.
Where the shape comes from
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.
We keep the lapel as its own pattern piece so it can be changed without re-cutting the body. The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.
The sheet we need before costing
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | burgundy |
| Lining | unlined with faced seams |
| Closure | covered button placket |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 100 pcs per colour |
What to check before bulk
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.
Changes we can make at sample stage
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Vent, back seam, or plain back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Single or double breasted front, without re-cutting the back.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Private label: woven label, care label and hangtag to your artwork.
The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.