Wholesale Charcoal Grey Tailored Blazer Office Dress
This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.
For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press.
Structure and seams
Most of the handwork sits in a handful of steps, and each one has a right order. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.
We keep the tailored as its own pattern piece so it can be changed without re-cutting the body. If the tailored is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.
A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | grey |
| Lining | fully lined, bagged hem |
| Closure | covered button placket |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 15-20 days with handwork |
| MOQ | 100 pcs per colour |
Where this style fails in production
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.
Customisation that does not break the price
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Vent, back seam, or plain back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.