Welcome to Bafinasa official website!

Wholesale Charcoal Grey Peak Lapel Blazer Office Dress

Source:News / Time:2026-11-14

Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. Most of the money in a Wholesale Charcoal Grey Peak Lapel Blazer Office Dress sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.

We keep the lapel as its own pattern piece so it can be changed without re-cutting the body. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Shoulder and neckline decide whether a Wholesale Charcoal Grey Peak Lapel Blazer Office Dress looks expensive. Both are set by the block, not by the sewing. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygrey
Liningunlined with faced seams
Closurestretch panel, no zip
Size run34-44 with a regional grade
Sample lead time12-18 days after spec sign-off
MOQ300 pcs per style

Where this style fails in production

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

Changes we can make at sample stage

  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Vent, back seam, or plain back.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top