Wholesale Charcoal Grey Single Breasted Blazer Office Dress
It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in grey, the inside is structure, and the two have to agree on the same sample. Written down, the request is wholesale charcoal grey single breasted blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.
Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.
How it is built
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.
We keep the single breasted as its own pattern piece so it can be changed without re-cutting the body. The single breasted is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.
Specification, item by item
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | grey |
| Lining | fully lined, bagged hem |
| Closure | concealed side zip |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 300 pcs per style |
Failure points worth designing out
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
Customisation that does not break the price
- Vent, back seam, or plain back.
- Single or double breasted front, without re-cutting the back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Private label: woven label, care label and hangtag to your artwork.
Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
