Wholesale White 2 Piece Blazer Office Dress Set for Office
A Wholesale White 2 Piece Blazer Office Dress Set for Office reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. A Wholesale White 2 Piece Blazer Office Dress Set for Office can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.
Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press.
How it is built
The build follows the same order on every size. These are the steps where the shape is won or lost. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.
When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates.
The sheet we need before costing
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | white |
| Lining | unlined with faced seams |
| Closure | concealed side zip |
| Size run | 34-44 with a regional grade |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 100 pcs per colour |
What to check before bulk
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.
What we can change for you
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Vent, back seam, or plain back.
- Single or double breasted front, without re-cutting the back.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.
If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
