Wholesale Navy Blue Blazer Office Dress
Written down, the request is wholesale navy blue blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in navy, the inside is structure, and the two have to agree on the same sample. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.
We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.
Structure and seams
Most of the handwork sits in a handful of steps, and each one has a right order. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.
We keep the lapel as its own pattern piece so it can be changed without re-cutting the body. The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | navy |
| Lining | fully lined, bagged hem |
| Closure | concealed side zip |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 300 pcs per style |
What to check before bulk
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.
Changes we can make at sample stage
- Vent, back seam, or plain back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Single or double breasted front, without re-cutting the back.
- Private label: woven label, care label and hangtag to your artwork.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
