Wholesale Charcoal Grey Double Breasted Blazer Office Dress

We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Written down, the request is wholesale charcoal grey double breasted blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

Where the shape comes from

Most of the handwork sits in a handful of steps, and each one has a right order. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.

We keep the double breasted as its own pattern piece so it can be changed without re-cutting the body. The double breasted is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.

The sheet we need before costing

The places this usually goes wrong

• Lining cut to the same length as the shell, so the dress climbs when worn.
• Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
• Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
• The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
• A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

Changes we can make at sample stage

• Lining to match or contrast. Contrast adds a visible detail at the cuff.
• Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
• Single or double breasted front, without re-cutting the back.
• Shoulder: soft pad, structured pad, or none with a clean finish.
• Shell swap: the same block in a lighter or heavier cloth, priced separately.
• Shell swap: the same block in a lighter or heavier cloth, priced separately.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.