Wholesale Burgundy Smart Casual Blazer Office Dress
The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Written down, the request is wholesale burgundy smart casual blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. A Wholesale Burgundy Smart Casual Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together.
Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth.
Construction notes
The build follows the same order on every size. These are the steps where the shape is won or lost. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.
When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | burgundy |
| Lining | fully lined, bagged hem |
| Closure | invisible centre-back zip |
| Size run | 34-44 with a regional grade |
| Sample lead time | 15-20 days with handwork |
| MOQ | 300 pcs per style |
Where this style fails in production
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.
Changes we can make at sample stage
- Single or double breasted front, without re-cutting the back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Vent, back seam, or plain back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
