Wholesale Navy Blue Corporate Blazer Dress
It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in navy, the inside is structure, and the two have to agree on the same sample. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel.
Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.
Construction notes
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.
The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. We keep the lapel as its own pattern piece so it can be changed without re-cutting the body.
On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
Specification, item by item
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | navy |
| Lining | unlined with faced seams |
| Closure | covered button placket |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 50 pcs sample order |
Where this style fails in production
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.
Changes we can make at sample stage
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Single or double breasted front, without re-cutting the back.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
