Wholesale Camel Tailored Blazer Office Dress
Most of the money in a Wholesale Camel Tailored Blazer Office Dress sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.
For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.
Where the shape comes from
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.
We keep the tailored as its own pattern piece so it can be changed without re-cutting the body. The tailored is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.
The sheet we need before costing
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | camel |
| Lining | unlined with faced seams |
| Closure | covered button placket |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 150 pcs per style |
What to check before bulk
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.
Changes we can make at sample stage
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Single or double breasted front, without re-cutting the back.
- Vent, back seam, or plain back.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
