Wholesale Double Breasted Blazer Office Dress Online
It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte, the inside is structure, and the two have to agree on the same sample. A Wholesale Double Breasted Blazer Office Dress Online can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.
Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.
Construction notes
Most of the handwork sits in a handful of steps, and each one has a right order. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.
The double breasted reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. We keep the double breasted as its own pattern piece so it can be changed without re-cutting the body.
Shoulder and neckline decide whether a Wholesale Double Breasted Blazer Office Dress Online looks expensive. Both are set by the block, not by the sewing. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
The sheet we need before costing
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | fully lined, bagged hem |
| Closure | invisible centre-back zip |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 50 pcs sample order |
Failure points worth designing out
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.
Changes we can make at sample stage
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Vent, back seam, or plain back.
- Single or double breasted front, without re-cutting the back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
