Wholesale Emerald Green Collarless Blazer Office Dress
The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in green, the inside is structure, and the two have to agree on the same sample. A Wholesale Emerald Green Collarless Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together.
Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.
Where the shape comes from
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.
The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. We keep the lapel as its own pattern piece so it can be changed without re-cutting the body.
If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | green |
| Lining | half lined to the hip |
| Closure | covered button placket |
| Size run | 34-44 with a regional grade |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 300 pcs per style |
What to check before bulk
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.
Changes we can make at sample stage
- Single or double breasted front, without re-cutting the back.
- Vent, back seam, or plain back.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Private label: woven label, care label and hangtag to your artwork.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
