Wholesale Black Structured Blazer Office Dress
The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Written down, the request is wholesale black structured blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.
Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.
How it is built
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.
We keep the lapel as its own pattern piece so it can be changed without re-cutting the body. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Shoulder and neckline decide whether a Wholesale Black Structured Blazer Office Dress looks expensive. Both are set by the block, not by the sewing.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | black |
| Lining | half lined to the hip |
| Closure | concealed side zip |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 15-20 days with handwork |
| MOQ | 150 pcs per style |
Where this style fails in production
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.
Customisation that does not break the price
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Single or double breasted front, without re-cutting the back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
