Wholesale Emerald Green Business Blazer Dress
The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in green, the inside is structure, and the two have to agree on the same sample. A Wholesale Emerald Green Business Blazer Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together.
Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.
Construction notes
Most of the handwork sits in a handful of steps, and each one has a right order. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.
The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | green |
| Lining | fully lined, bagged hem |
| Closure | concealed side zip |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 15-20 days with handwork |
| MOQ | 100 pcs per colour |
What to check before bulk
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.
Options on the table
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Single or double breasted front, without re-cutting the back.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
