Wholesale Navy Blue Long Sleeve Blazer Office Dress
Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount.
Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.
How it is built
Most of the handwork sits in a handful of steps, and each one has a right order. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.
If the long sleeve is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. The long sleeve is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel.
The sheet we need before costing
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | navy |
| Lining | fully lined, bagged hem |
| Closure | covered button placket |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 15-20 days with handwork |
| MOQ | 50 pcs sample order |
The places this usually goes wrong
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
Options on the table
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Single or double breasted front, without re-cutting the back.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
