Double Breasted Blazer Office Dress Wholesale

We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. A Double Breasted Blazer Office Dress Wholesale reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

The double breasted is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. If the double breasted is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.

What goes on the spec sheet

What to check before bulk

• Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
• Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
• Lining cut to the same length as the shell, so the dress climbs when worn.
• Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
• The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

Customisation that does not break the price

• Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
• Vent, back seam, or plain back.
• Single or double breasted front, without re-cutting the back.
• Lining to match or contrast. Contrast adds a visible detail at the cuff.
• Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
• Private label: woven label, care label and hangtag to your artwork.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.