Single Breasted Blazer Office Dress Wholesale
There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. A Single Breasted Blazer Office Dress Wholesale can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Written down, the request is single breasted blazer office dress wholesale: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.
Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.
Construction notes
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.
The single breasted reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. The single breasted is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Shoulder and neckline decide whether a Single Breasted Blazer Office Dress Wholesale looks expensive. Both are set by the block, not by the sewing.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | bodice lined, skirt lined |
| Closure | concealed side zip |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 50 pcs sample order |
What to check before bulk
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.
Customisation that does not break the price
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Vent, back seam, or plain back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
