Welcome to Bafinasa official website!

Heather Grey Midi Blazer Office Dress for Office

Source:News / Time:2026-11-14

Most of the money in a Heather Grey Midi Blazer Office Dress for Office sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel.

Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.

Where the shape comes from

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

We keep the lapel as its own pattern piece so it can be changed without re-cutting the body. The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthmidi
Colourwaygrey
Liningunlined with faced seams
Closureinvisible centre-back zip
Size runS-3XL graded to your sheet
Sample lead time10-14 days on stock cloth
MOQ300 pcs per style

What to check before bulk

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing.

Customisation that does not break the price

  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Single or double breasted front, without re-cutting the back.
  • Vent, back seam, or plain back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Private label: woven label, care label and hangtag to your artwork.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top