Welcome to Bafinasa official website!

Women's Chic Black A-line Blazer Office Dress

Source:News / Time:2026-11-14

Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in black, the inside is structure, and the two have to agree on the same sample.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. We keep the lapel as its own pattern piece so it can be changed without re-cutting the body.

On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

What goes on the spec sheet

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwayblack
Liningbodice lined, skirt lined
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ100 pcs per colour

What to check before bulk

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Changes we can make at sample stage

  • Single or double breasted front, without re-cutting the back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Vent, back seam, or plain back.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top