Welcome to Bafinasa official website!

Light Grey Tailored Blazer Office Dress

Source:News / Time:2026-11-14

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Written down, the request is light grey tailored blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. A Light Grey Tailored Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together.

Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.

The tailored reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. If the tailored is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel.

What goes on the spec sheet

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygrey
Lininghalf lined to the hip
Closureinvisible centre-back zip
Size runS-3XL graded to your sheet
Sample lead time10-14 days on stock cloth
MOQ300 pcs per style

What to check before bulk

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.

Customisation that does not break the price

  • Single or double breasted front, without re-cutting the back.
  • Vent, back seam, or plain back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top