Welcome to Bafinasa official website!

Heather Grey Double Breasted Blazer Office Dress

Source:News / Time:2026-11-14

This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.

Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

Where the shape comes from

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

When the brief names the double breasted, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. We keep the double breasted as its own pattern piece so it can be changed without re-cutting the body.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.

What goes on the spec sheet

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygrey
Liningfully lined, bagged hem
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ150 pcs per style

What to check before bulk

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

What we can change for you

  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Single or double breasted front, without re-cutting the back.
  • Vent, back seam, or plain back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top