Welcome to Bafinasa official website!

Heather Grey Midi Blazer Office Dress

Source:News / Time:2026-11-14

Most of the money in a Heather Grey Midi Blazer Office Dress sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. A Heather Grey Midi Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

Where the shape comes from

The build follows the same order on every size. These are the steps where the shape is won or lost. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.

Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthmidi
Colourwaygrey
Liningbodice lined, skirt lined
Closurestretch panel, no zip
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ100 pcs per colour

What to check before bulk

  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

Changes we can make at sample stage

  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Single or double breasted front, without re-cutting the back.
  • Private label: woven label, care label and hangtag to your artwork.
  • Private label: woven label, care label and hangtag to your artwork.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top