Welcome to Bafinasa official website!

Tailored Black Tailored Blazer Office Dress

Source:News / Time:2026-11-14

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Tailored Black Tailored Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in black, the inside is structure, and the two have to agree on the same sample. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.

Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

Construction notes

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.

Check the tailored after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The tailored is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Shoulder and neckline decide whether a Tailored Black Tailored Blazer Office Dress looks expensive. Both are set by the block, not by the sewing. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwayblack
Liningunlined with faced seams
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time15-20 days with handwork
MOQ300 pcs per style

Failure points worth designing out

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.

What we can change for you

  • Single or double breasted front, without re-cutting the back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Vent, back seam, or plain back.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top