Welcome to Bafinasa official website!

Charcoal Grey Corporate Blazer Dress

Source:News / Time:2026-11-14

We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel.

For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Shoulder and neckline decide whether a Charcoal Grey Corporate Blazer Dress looks expensive. Both are set by the block, not by the sewing. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygrey
Liningfully lined, bagged hem
Closureconcealed side zip
Size run34-44 with a regional grade
Sample lead time10-14 days on stock cloth
MOQ100 pcs per colour

What to check before bulk

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

Changes we can make at sample stage

  • Single or double breasted front, without re-cutting the back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top