Welcome to Bafinasa official website!

Heather Grey Tailored Blazer Office Dress for Office

Source:News / Time:2026-11-14

This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. A Heather Grey Tailored Blazer Office Dress for Office reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.

The tailored reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. If the tailored is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

Shoulder and neckline decide whether a Heather Grey Tailored Blazer Office Dress for Office looks expensive. Both are set by the block, not by the sewing. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygrey
Liningfully lined, bagged hem
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time10-14 days on stock cloth
MOQ100 pcs per colour

The places this usually goes wrong

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

Customisation that does not break the price

  • Single or double breasted front, without re-cutting the back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top