Welcome to Bafinasa official website!

2 Piece Blazer Office Dress Set

Source:News / Time:2026-11-14

This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. A 2 Piece Blazer Office Dress Set reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. If the lapel is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. Shoulder and neckline decide whether a 2 Piece Blazer Office Dress Set looks expensive. Both are set by the block, not by the sewing. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningunlined with faced seams
Closurestretch panel, no zip
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

Where this style fails in production

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Options on the table

  • Single or double breasted front, without re-cutting the back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top