Welcome to Bafinasa official website!

Light Grey Belted Blazer Office Dress for Office

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.

Check the belted after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. When the brief names the belted, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

Shoulder and neckline decide whether a Light Grey Belted Blazer Office Dress for Office looks expensive. Both are set by the block, not by the sewing. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygrey
Liningunlined with faced seams
Closurestretch panel, no zip
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

What to check before bulk

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Options on the table

  • Single or double breasted front, without re-cutting the back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Private label: woven label, care label and hangtag to your artwork.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top