Modern Black Double Breasted Blazer Office Dress
This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Most of the money in a Modern Black Double Breasted Blazer Office Dress sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. A Modern Black Double Breasted Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.
Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.
Construction notes
The build follows the same order on every size. These are the steps where the shape is won or lost. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.
We keep the double breasted as its own pattern piece so it can be changed without re-cutting the body. Check the double breasted after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.
The sheet we need before costing
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | black |
| Lining | bodice lined, skirt lined |
| Closure | covered button placket |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 100 pcs per colour |
What to check before bulk
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
What we can change for you
- Vent, back seam, or plain back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Single or double breasted front, without re-cutting the back.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.