Welcome to Bafinasa official website!

Tailored Black Notch Lapel Blazer Office Dress

Source:News / Time:2026-11-14

A Tailored Black Notch Lapel Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. A Tailored Black Notch Lapel Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows.

Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

Where the shape comes from

Most of the handwork sits in a handful of steps, and each one has a right order. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.

We keep the tailored as its own pattern piece so it can be changed without re-cutting the body. When the brief names the tailored, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Shoulder and neckline decide whether a Tailored Black Notch Lapel Blazer Office Dress looks expensive. Both are set by the block, not by the sewing. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel.

What goes on the spec sheet

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwayblack
Liningfully lined, bagged hem
Closurestretch panel, no zip
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

Failure points worth designing out

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

What we can change for you

  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Single or double breasted front, without re-cutting the back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Private label: woven label, care label and hangtag to your artwork.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top