Welcome to Bafinasa official website!

Women's Light Grey Work Blazer Dress

Source:News / Time:2026-11-14

Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. A Women's Light Grey Work Blazer Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth.

How it is built

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.

We keep the lapel as its own pattern piece so it can be changed without re-cutting the body. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygrey
Liningbodice lined, skirt lined
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time12-18 days after spec sign-off
MOQ50 pcs sample order

Where this style fails in production

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

Customisation that does not break the price

  • Single or double breasted front, without re-cutting the back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Vent, back seam, or plain back.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top