Welcome to Bafinasa official website!

Board Meeting Burgundy Pleated Blazer Office Dress

Source:News / Time:2026-11-14

We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in burgundy, the inside is structure, and the two have to agree on the same sample.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.

Where the shape comes from

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.

The pleated is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. When the brief names the pleated, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Shoulder and neckline decide whether a Board Meeting Burgundy Pleated Blazer Office Dress looks expensive. Both are set by the block, not by the sewing. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwayburgundy
Lininghalf lined to the hip
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ100 pcs per colour

What to check before bulk

  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Options on the table

  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Single or double breasted front, without re-cutting the back.
  • Vent, back seam, or plain back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top