Women's Tailored Black Midi Blazer Office Dress
Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Women's Tailored Black Midi Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in black, the inside is structure, and the two have to agree on the same sample.
Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Request a shrink test on the actual dye lot. Half a percent across a midi is visible to the customer and invisible on the sheet. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.
How it is built
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.
When the brief names the tailored, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. Check the tailored after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.
The sheet we need before costing
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | midi |
| Colourway | black |
| Lining | half lined to the hip |
| Closure | invisible centre-back zip |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 300 pcs per style |
What to check before bulk
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.
Changes we can make at sample stage
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Vent, back seam, or plain back.
- Single or double breasted front, without re-cutting the back.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.